Sealing and lubrication elements
Sealing and lubrication elements – system KIT
With their extensive range of standard accessories, the linear guidance systems can be easily used in numerous areas. Since the guidance systems are used in an extremely wide variety of applications, however, additional requirements are often placed on the lubrication and sealing components.
Application-oriented complete package
If the standard components are not adequate for reliable operation and a long operating life, it is possible to draw on a finely graduated system of sealing and lubrication elements. These special accessories protect the rolling element system of the guidance systems against contamination and ensure long relubrication intervals even under the most demanding operating conditions.
KIT structure
The elements are configured as the system KIT and are designed for various application conditions.
Starting from the degree of contamination, the best combination in each case can be quickly and easily compiled:
- Possible combinations, see link and link
- Description of sealing elements, see link
- Overview of sealing elements, see link and link
- Description of lubrication elements, see link
- Overview of lubrication elements, see link and link.
ACHTUNG
Only a proportion of the KITs can be retrofitted. Parts that cannot be retrofitted must be ordered together with the linear recirculating ball bearing and guideway assembly and are supplied already fitted.
Degree of contamination
The degree of contamination will vary depending on the market sector, the application and the environmental conditions.
ACHTUNG
The definitions at this point are therefore only an initial aid in the selection of KITs.
Definition of the degree of contamination
Degree of contamination | |||
---|---|---|---|
Very slight | Slight | Moderate | Heavy** |
Clean environment. | Coarse (large) metal swarf Clean environment No cooling lubricants. | Coarse (large) metal swarf Slight exposure to, for example, cooling lubricants. | Hot swarf Aggressive media and dust as well as cooling lubricants. |
**If this degree of contamination is present, a KIT can give only a restricted level of protection. Additional measures implemented by the customer, such as additional covers on the guidance system, will give a considerable increase in the operating life.
Sealing elements
Additional sealing elements are available both for open upper lubrication holes as well as for close upper lubrication holes:
End plates
End plates are corrosion-resistant, non-contact components, ➤ Figure. They protect the end wipers located behind them against, for example, coarse contaminants and hot swarf. There is a narrow gap between the guideway and the seal.
End plate
KIT.KWVE..-210
non-contact
End wipers
End wipers are contact seals that are fixed to the end faces of the carriages. End wipers protect the guidance system against the ingress of contaminant particles and can extend the relubrication intervals. The selection of the suitable sealing system is based on the application of the guidance system. End wipers are available as a gap seal (grey), single lip smooth-running end wiper (green) and a single lip end wiper (black) with increased sealing action, ➤ Figure.
Single lip end wipers (green, black) have a seal lip oriented outwards that protects the carriage against the ingress of contaminant particles. In combination with oil lubrication, the single lip end wiper facilitates the rinsing out of contaminant particles (flushing effect).
Gap seals are non-contact seals. They have a small gap around the contour of the guideway. There is no increase in displacement force. The gap seal should only be used in a clean environment.
End wipers
Example KIT.KWVE..-110, -100, KIT.KWVE..-220 (with end plate)
single lip, black · Standard: Smooth-running end wiper,
single lip, green
High-Speed
Linear recirculating ball bearing and guideway assemblies of the series High-Speed are only available in a standard KIT combination (120/900/120). It is not necessary to indicate this when ordering.
End wiper KIT.KWVE25B-120
ACHTUNG
Since the series High-Speed has an optimised end piece, KIT.KWVE25-B-120 can only be used for this version. Other KIT combinations are not available.
Additional wipers
Additional wipers
with squeeze plate
In addition to the standard seal, other additional wipers may be used behind each other (cascading arrangement). These are screw mounted with a squeeze plate in front of the first wiper on the carriage, ➤ Figure.
The additional wipers are of a single or double lip design and are made from special high performance material.
Double lip additional wipers with a squeeze plate have one seal lip oriented outwards and one seal lip oriented inwards. The seal lip oriented inwards prevents the escape of lubricant from the carriage, which means that an increase in the relubrication interval can be achieved. Double lip end wipers are recommended for use with grease lubrication (reservoir lubrication).
Additional wipers Example KIT.KWVE..-300, -370
Additional wipers
Additional wipers for heavy contamination, such as dust or liquids, are used in combination with further wipers.
Additional wipers are of a single lip design and are made from FPM, ➤ Figure.
Additional wiper Example KIT.KWVE..-320
single lip
Sealing strips
Sealing strips are contact components that are fitted to the upper and lower longitudinal sides of the carriage, ➤ Figure. They protect the rolling element system against contamination and loss of lubricant.
Single lip
Linear recirculating ball bearing and guideway assemblies are available with a single lip upper sealing strip as well as a single lip lower sealing strip.
ACHTUNG
Upper sealing strips should be used in addition to end wipers and lower sealing strips especially in applications where lubrication is critical, such as those involving fine dust or aggressive coolants.
Sealing strips KIT.KWVE..-900, -910
single lip · Upper sealing strips,
single lip
Lubrication elements
A long term lubrication unit is available as a lubrication component.
Long term lubrication unit KIT series 400
For linear recirculating ball bearing and guideway assemblies KUVE, KITs with a long term lubrication unit are available.
Operating life
of the linear guidance system
The operating life is defined as the life actually achieved by a linear guidance system. This may deviate significantly from the basic rating life.
A sufficiently long operating life is only achieved, assuming the bearing arrangement is correctly designed, through optimum lubrication and sealing. This can be achieved using the long term lubrication unit, ➤ Figure.
Grease operating life
and relubrication interval
If guidance systems cannot be relubricated, the grease operating life becomes the decisive factor. This indicates the length of time for which a grease can be used without its function being impaired.
As the load increases, the grease is subjected to increasing strain. As a result, it ages more quickly. Premature destruction of the grease structure has an adverse effect on the performance characteristics of the grease. The grease operating life declines and relubrication must be carried out earlier.
If the shortened relubrication intervals are not observed, the guidance system will fail before the end of the expected operating life. With decreasing grease operating life, the operating life of the linear guidance system is thus reduced.
Longer operating life by means of a long term lubrication unit
The volume of lubricating grease in the carriage is increased by the lubrication pockets in the saddle plate. If a long term lubrication unit of KIT series 400 is also fitted, this gives an additional improvement in the lubricant balance, ➤ Figure. The lubricant is stored in a high capacity reservoir and continuously released to the raceways via a transfer medium. Depending on the operating and environmental conditions, it is possible to achieve long relubrication intervals or even complete freedom from maintenance.
The operating life of four-row linear recirculating ball bearing and guideway assemblies KUVE..-B with and without a long term lubrication unit is shown in ➤ Figure.
Function irrespective of position
Long term lubrication units are particularly suitable in applications where lubrication is of critical importance. They are screw mounted between the end piece and the wiper and function with equal reliability in either a horizontal or vertical mounting position.
Long term lubrication unit
double lip, with squeeze plate · Long term lubrication unit
With initial greasing
Due to their initial greasing, long term lubrication units are ready for immediate operation. If they are ordered together with a KUVE, both the linear recirculating ball bearing and guideway assembly KUVE and the long term lubrication unit have an initial greasing.
ACHTUNG
If the long term lubrication unit is retrofitted, it is absolutely essential that the carriage is given an initial greasing.
The long term lubrication unit must always be used on both sides of the carriage, in order to achieve the stated bearing factor KLF and thus the maximum operating life.
Double lip end seal
Integrated double lip end seals give protection against grease loss and contamination.
Operating life with and without long term lubrication unit
(restricted by material fatigue) · KUVE without long term lubrication unit
(restricted by material fatigue) · Competitor systems
Configuration of KIT.KWVE
Unless indicated otherwise, the locating edge is defined as being at the top. The KIT designation is given in the sequence left/centre/right. If no KIT numbers are indicated, the standard version will be supplied, see tables Sealing and lubrication elements KIT for KUVE...-B, link, and for KUVE..-W, link.
KIT components can be fitted on the left, centre and right of the carriage, ➤ Figure.
Example of KIT configuration
Retrofitting by the customer
The KITs available for retrofitting by the customer are indicated accordingly as retrofittable in the KIT tables, see link and link.
KIT left, right
The KIT components are identical for all carriage designs.
KIT components for retrofitting by the customer of the linear recirculating ball bearing and guideway assembly KUVE-..B must be ordered for all types and designs using the designation KIT.KWVE..-B.
KIT components for retrofitting by the customer of the linear recirculating ball bearing and guideway assembly KUVE-..W must be ordered for all types and designs using the designation KIT.KWVE..-W.
The scope of delivery includes the wear components and fixing screws required for retrofitting.
Example: KIT.KWVE20-B-330.
KIT centre
If retrofitting is to be carried out by the customer, attention must be paid to the carriage length.
KIT components for retrofitting by the customer of long carriages must be ordered using the designation KIT.KWVE..-B-L-900.
KIT components for retrofitting by the customer of short carriages must be ordered using the designation KIT.KWVE..-B-C-900.
Example: KIT.KWVE20-B-L-900.
Sealing and lubrication elements KIT (left, right)
for KUVE..-B
Designation and KIT end number | Image | Description | Degree of contamination | Size | Retrofittable | Tolerances | Increased displacement force | Designation and KIT end number | |||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
slight | medium | heavy | K1 | LS | S | none | slight | moderate | heavy | ||||||
KIT.KWVE..-B | mm | mm | KIT.KWVE..-B | ||||||||||||
000 | – | No KIT at the corresponding location. | █ | – | – | 15 | █ | – | – | –0,8 | █ | – | – | – | 000 |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 | |||||||||||||||
45 | |||||||||||||||
55 | |||||||||||||||
100 | End wiper, contact type, single lip. | █ | █ | – | 15 | █ | – | – | –0,8 | – | – | █ | – | 100 | |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 | |||||||||||||||
45 | |||||||||||||||
55 | |||||||||||||||
110 | Gap seals. | █ | – | – | 15 | █ | – | – | –0,8 | █ | – | – | – | 110 | |
20 | |||||||||||||||
25 | |||||||||||||||
– | |||||||||||||||
– | |||||||||||||||
– | |||||||||||||||
– | |||||||||||||||
200 | Fixing screw K1 Sheet steel wiper, non-contact End wiper, contact type, single lip. | █ | █ | – | 15 | █ | M2×4 | 1,3 | 0 | – | – | █ | – | 200 | |
20 | M2×4 | 1,3 | |||||||||||||
25 | M3×5 | 1,65 | |||||||||||||
30 | M3×5 | 1,65 | |||||||||||||
35 | M3×5 | 1,65 | |||||||||||||
45 | M4×6 | 2,2 | |||||||||||||
55 | M4×6 | 2,2 | |||||||||||||
210 | Fixing screw K1 Sheet steel wiper, non-contact. | █ | – | – | 15 | █ | M2×4 | 1,3 | 0 | █ | – | – | – | 210 | |
20 | M2×4 | 1,3 | |||||||||||||
25 | M3×5 | 1,65 | |||||||||||||
30 | M3×5 | 1,65 | |||||||||||||
35 | M3×5 | 1,65 | |||||||||||||
45 | M4×6 | 2,2 | |||||||||||||
55 | M4×6 | 2,2 | |||||||||||||
Designation and KIT end number | Image | Description | Degree of contamination | Size | Retrofittable | Tolerances | Increased displacement force | Designation and KIT end number | |||||||
slight | medium | heavy | K1 | LS | S | none | slight | moderate | heavy | ||||||
KIT.KWVE..-B | mm | mm | KIT.KWVE..-B | ||||||||||||
220** | Fixing screw K1 Sheet steel wiper, non-contact Smooth-running end wiper contact type, single lip. | █ | – | – | 15 | █ | M2×4 | 1,3 | 0 | – | █ | – | – | 220** | |
20 | M2×4 | 1,3 | |||||||||||||
25 | M3×5 | 1,65 | |||||||||||||
30 | M3×5 | 1,65 | |||||||||||||
35 | M3×5 | 1,65 | |||||||||||||
45 | M4×6 | 2,2 | |||||||||||||
55 | M4×6 | 2,2 | |||||||||||||
300 | Fixing screw K1 End wiper, contact type, single lip End seal, single lip (PU) with pressing plate. | █ | █ | █ | 15 | █ | M2×8 | 1,3 | 4,2 | – | – | – | █ | 300 | |
20 | M2×8 | 1,3 | |||||||||||||
25 | M3×8 | 1,65 | |||||||||||||
30 | M3×8 | 1,65 | |||||||||||||
35 | M3×8 | 1,65 | |||||||||||||
45 | M4×10 | 2,2 | |||||||||||||
55 | M4×10 | 2,2 | |||||||||||||
310 | Fixing screw K1 Sheet steel wiper, non-contact End wiper, contact type, single lip End seal, single lip (PU) with pressing plate. | █ | █ | █ | 15 | █ | M2×9 | 1,3 | 5,0 | – | – | – | █ | 310 | |
20 | M2×9 | 1,3 | |||||||||||||
25 | M3×10 | 1,65 | |||||||||||||
30 | M3×10 | 1,65 | |||||||||||||
35 | M3×10 | 1,65 | |||||||||||||
45 | M4×10 | 2,2 | |||||||||||||
55 | M4×10 | 2,2 | |||||||||||||
320 | Fixing screw K1 End wiper, contact type, single lip Additional wiper, single lip (FPM). | █ | █ | █ | – | █ | – | – | – | – | – | – | █ | 320 | |
20 | M2×8 | 1,3 | 3,7 | ||||||||||||
25 | M3×8 | 1,65 | |||||||||||||
30 | M3×8 | 1,65 | |||||||||||||
35 | M3×8 | 1,65 | |||||||||||||
45 | M4×10 | 2,2 | |||||||||||||
– | – | – | – | ||||||||||||
330 | Fixing screw K1 Sheet steel wiper, non-contact End wiper, contact type, single lip Additional wiper, single lip (FPM). | █ | █ | █ | – | █ | – | – | – | – | – | – | █ | 330 | |
20 | M2×8 | 1,3 | 4,5 | ||||||||||||
25 | M3×8 | 1,65 | |||||||||||||
30 | M3×8 | 1,65 | |||||||||||||
35 | M3×8 | 1,65 | |||||||||||||
45 | M4×10 | 2,2 | |||||||||||||
– | – | – | – | ||||||||||||
Designation and KIT end number | Image | Description | Degree of contamination | Size | Retrofittable | Tolerances | Increased displacement force | Designation and KIT end number | |||||||
slight | medium | heavy | K1 | LS | S | none | slight | moderate | heavy | ||||||
KIT.KWVE..-B | mm | mm | KIT.KWVE..-B | ||||||||||||
360 | Fixing screw K1 Sheet steel wiper, non-contact Additional wiper, double lip (PU) with pressing plate. | █ | █ | █ | 15 | █ | M2×9 | 1,3 | 5 | – | – | – | █ | 360 | |
20 | M2×9 | 1,3 | |||||||||||||
25 | M3×10 | 1,65 | |||||||||||||
30 | M3×10 | 1,65 | |||||||||||||
35 | M3×10 | 1,65 | |||||||||||||
45 | M4×10 | 2,2 | |||||||||||||
55 | M4×10 | 2,2 | |||||||||||||
370 | Fixing screw K1 Additional wiper, double lip (PU) with pressing plate. | █ | █ | – | 15 | █ | M2×8 | 1,3 | 4,2 | – | – | – | █ | 370 | |
20 | M2×8 | 1,3 | |||||||||||||
25 | M3×8 | 1,65 | |||||||||||||
30 | M3×8 | 1,65 | |||||||||||||
35 | M3×8 | 1,65 | |||||||||||||
45 | M4×10 | 2,2 | |||||||||||||
55 | M4×10 | 2,2 | |||||||||||||
400 | Fixing screw K1 Additional wiper, double lip (PU) with pressing plate Long term lubrication unit. | █ | █ | – | 15 | █ | M2×17 | 1,3 | 14,1 | – | – | – | █ | 400 | |
20 | M2×17 | 1,3 | 13,2 | ||||||||||||
25 | M3×18 | 1,65 | 13,2 | ||||||||||||
30 | M3×18 | 1,65 | 13,2 | ||||||||||||
35 | M3×18 | 1,65 | 13,2 | ||||||||||||
45 | M4×20 | 2,2 | 14,7 | ||||||||||||
– | – | – | – | ||||||||||||
430 | Fixing screw K1 Sheet steel wiper, non-contact Additional wiper, double lip (PU) with pressing plate Long term lubrication unit. | █ | █ | █ | 15 | █ | M2×18 | 1,3 | 14,9 | – | – | – | █ | 430 | |
20 | M2×18 | 1,3 | 14 | ||||||||||||
25 | M3×19 | 1,65 | 14 | ||||||||||||
30 | M3×19 | 1,65 | 14 | ||||||||||||
35 | M3×19 | 1,65 | 14 | ||||||||||||
45 | M4×22 | 2,2 | 15,5 | ||||||||||||
– | – | – | – |
Locating face
ACHTUNG
The table is only intended as a guide. Specific application conditions must be taken into consideration when selecting the elements.
The sealing and lubrication elements KIT can be combined flexibly. Recommended and possible combinations, see link. Recommended lubrication connectors, see link.
**Standard for KUVE..-B.
Sealing and lubrication element KIT (centre)
for KUVE..-B
Designation and KIT end number | Image | Description | Degree of contamination | Size | Retrofittable | Tolerances | Increased displacement force | Designation and KIT end number | |||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
slight | medium | heavy | K1 | LS | S | none | slight | moderate | heavy | ||||||
KIT.KWVE..-B** | mm | mm | KIT.KWVE..-B** | ||||||||||||
000 | – | No KIT at the corresponding location. | █ | – | – | 15 | █ | – | – | – | █ | – | – | – | 000 |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 | |||||||||||||||
45 | |||||||||||||||
55 | |||||||||||||||
900** | Lower sealing strip, single lip. | █ | █ | – | 15 | █ | – | – | – | – | █ | – | – | 900** | |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 | |||||||||||||||
45 | |||||||||||||||
55 | |||||||||||||||
910 | Lower sealing strip, single lip Upper sealing strip, single lip. | █ | █ | █ | 15 | – | – | – | – | – | – | █ | – | 910 | |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 | |||||||||||||||
45 | |||||||||||||||
55 |
ACHTUNG
The table is only intended as a guide. Specific application conditions must be taken into consideration when selecting the elements.
The sealing and lubrication elements KIT can be combined flexibly. Recommended and possible combinations, see link. Recommended lubrication connectors, see link.
**If retrofitting is to be carried out by the customer, attention must be paid to the carriage length. See Retrofitting by the customer, link.
**Standard for KUVE..-B.
Possible combinations – KIT allocation (left) to KIT right | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Designation and |
| |||||||||||||
KIT.KWVE..-B | 000 | 100 | 110 | 200 | 210 | 220 | 300 | 310 | 320 | 330 | 360 | 370 | 400 | 430 |
000 | ● | ‒ | ● | ‒ | ● | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ |
100 | ‒ | ● | ‒ | ● | ‒ | ● | ● | ● | ● | ● | ● | ● | ‒ | ‒ |
110 | ● | ‒ | ● | ‒ | ● | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ |
200 | ‒ | ● | ‒ | ● | ‒ | ● | ● | ● | ● | ● | ● | ● | ‒ | ‒ |
210 | ● | ‒ | ● | ‒ | ● | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ |
220 | ‒ | ● | ‒ | ● | ‒ | ● | ● | ● | ● | ● | ● | ● | ‒ | ‒ |
300 | ‒ | ● | ‒ | ● | ‒ | ● | ● | ● | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ |
310 | ‒ | ● | ‒ | ● | ‒ | ● | ● | ● | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ |
320 | ‒ | ● | ‒ | ● | ‒ | ● | ‒ | ‒ | ● | ● | ‒ | ‒ | ‒ | ‒ |
330 | ‒ | ● | ‒ | ● | ‒ | ● | ‒ | ‒ | ● | ● | ‒ | ‒ | ‒ | ‒ |
360 | ‒ | ● | ‒ | ● | ‒ | ● | ‒ | ‒ | ‒ | ‒ | ● | ● | ‒ | ‒ |
370 | ‒ | ● | ‒ | ● | ‒ | ● | ‒ | ‒ | ‒ | ‒ | ● | ● | ‒ | ‒ |
400 | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ● | ● |
430 | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ● | ● |
●
Possible combination.
Possible combinations – KIT allocation (left or right) to KIT centre | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Designation and |
| |||||||||||||
KIT.KWVE..-B | 000 | 100 | 110 | 200 | 210 | 220 | 300 | 310 | 320 | 330 | 360 | 370 | 400 | 430 |
000 | ● | ‒ | ● | ‒ | ● | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ |
900 | ‒ | ● | ‒ | ● | ‒ | ● | ● | ● | ● | ● | ● | ● | ● | ● |
910 | ‒ | ● | ‒ | ● | ‒ | ● | ● | ● | ● | ● | ● | ● | ● | ● |
●
Possible combination.
Definition of side allocation
ACHTUNG
The side allocation of the KIT (left, centre, right) is independent of the orientation of the locating face. When ordering, the required orientation of the locating face (top or bottom) must be indicated.
Lubrication connectors for KUVE..-B
Standard lubrication connectors
Lubrication connectors for manual lubricators
Lubrication connectors for manual lubricators
Size | Designation | Positions: | Positions: | ||||||
---|---|---|---|---|---|---|---|---|---|
Thread | Straight | Angled (45°) | Thread | Straight | |||||
KIT | KIT | KIT | |||||||
KUVE..-B | 000 100 110 200 210 220 | 300 310 320 330 360 370 | 000 100 110 200 210 220 | 300 310 320 330 360 370 | 000 100 110 200 210 220 | 300 310 320 330 360 370 | |||
15 | All | M3 | S16** | S12 | ‒ | ‒ | M3 | S16 | S16 |
20 | -E, -EC, -N, -NL, | M5 | S02 | S75 | S04** | S13 | M3 | S16 | S16 |
-B, -L, -H, -HL, -S, -SL | M5 | S02 | S02 | ||||||
25 | -E, -EC, -N, -NL, | M6 | S03 | ‒ | S05** | S14 | M3 | S16 | S16 |
-B, -L, -H, -HL, -S, -SL | M6 | S03 | S03 | ||||||
30 | -N, -NL, -SN, -SNL | M6 | S03 | S51 | S05** | S14 | M5 | S02 | S02 |
-B, -L, -E, -EC, -H, -HL, | M6 | S03 | S03 | ||||||
35 | All | M6 | S03 | S51 | S05** | S14 | M6 | S03 | S03 |
45 | All | M6 | S03 | S51 | S05** | S14 | M6 | S03 | S03 |
55 | All | M6 | S03 | S51 | S05** | S14 | M6 | S03 | S03 |
**Standard.
Definition of lubrication connectors
ACHTUNG
The position and alignment of the lubrication connectors is independent of the orientation of the locating face. When ordering, the required orientation of the locating face (top or bottom) must be indicated.
Lubrication connectors for central lubrication
Lubrication connectors for central lubrication
Size | Designation | Positions: | Positions: | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread | Straight | Angled (90°) | Thread | Straight | |||||||||
KIT | KIT | KIT | |||||||||||
KUVE..-B | 000 100 110 | 200 210 220 | 300 310 320 330 360 370 | 000 100 110 | 200 210 220 | 300 | 310 320 330 360 | 370 | 000 100 110 200 210 220 | 300 310 320 330 360 370 | |||
15 | All | M3 | S07 | S48 | S71 | S49 | S49 | ‒ | ‒ | ‒ | M3 | S07 | S07 |
20 | -E, -EC, | M5 | S08 | S08 | S76 | S44 | S46 | ‒ |
| ‒ | M3 | S07 | S07 |
-B, -L, | M5 | S08 | S08 | ||||||||||
25 | -E, -EC, | M6 | S09 | S09 | S11 | S28 | S61 | S18 | S18 | S18 S68 | M3 | S07 | S07 |
-B, -L, | M6 | S09 | S09 | ||||||||||
30 | -N, -NL, | M6 | S09 | S09 | S11 | S28 | S61 | S18 S64 | S18 | S18 S68 | M5 | S08 | S08 |
-B, -L, | M6 | S09 | S09 | ||||||||||
35 | All | M6 | S09 | S09 | S11 | S28 | S61 | S18 S64 | S18 | S18 S64 | M6 | S09 | S09 |
45 | All | M6 | S09 | S09 | S11 | S28 | S61 | S18 S64 | S18 | S18 S64 | M6 | S09 | S09 |
55 | All | M6 | S09 | S09 | S11 | S28 | S61 | S18 S64 | S18 | ‒ | M6 | S09 | S09 |
**Not permissible for KIT320.
Definition of lubrication connectors
ACHTUNG
The position and alignment of the lubrication connectors is independent of the orientation of the locating face. When ordering, the required orientation of the locating face (top or bottom) must be indicated.
Sealing and lubrication elements KIT (left, right)
for KUVE..-W
Designation and KIT end number | Image | Description | Degree of contamination** | Size | Retrofittable | Tolerances | Increased displacement force | Designation and KIT end number | |||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
slight | medium | heavy | K1 | LS | S | none | slight | moderate | heavy | ||||||
KIT.KWVE..-W | mm | mm | KIT.KWVE..-W | ||||||||||||
000 | – | No KIT at the corresponding location. | █ | – | – | 15 | █ | – | – | – | █ | – | – | – | 000 |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 | |||||||||||||||
100** | Fixing screw K1 End wiper contact type, single lip. | █ | █ | – | 15 | █ | – | – | 0 | – | – | █ | – | 100** | |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 | |||||||||||||||
200 | Fixing screw K1 Sheet metal wiper non-contact End wiper contact type, single lip. | █ | █ | – | 15 | █ | M2×12 | 2 | 0,8 | – | – | █ | – | 200 | |
20 | M2,5×16 | 2,5 | |||||||||||||
25 | M3×16 | 3 | |||||||||||||
30 | M3×20 | 3 | |||||||||||||
35 | M4×22 | 4 | |||||||||||||
300 | Fixing screw K1 End wiper contact type, single lip Additional wiper single lip (NBR). | █ | █ | █ | – | █ | – | – | – | – | – | – | █ | 300 | |
20 | M2,5×18 | 1,5 | 4,5 | ||||||||||||
25 | M3×18 | 1,65 | |||||||||||||
30 | M3×22 | 1,65 | |||||||||||||
35 | M4×25 | 2,2 | |||||||||||||
370 | Fixing screw K1 Additional wiper double lip (NBR). | █ | █ | – | – | █ | – | – | – | – | – | – | █ | 370 | |
20 | M2,5×18 | 1,5 | 4,5 | ||||||||||||
25 | M3×18 | 1,65 | |||||||||||||
30 | M3×22 | 1,65 | |||||||||||||
35 | M4×25 | 2,2 | |||||||||||||
400 | Fixing screw K1 Additional wiper double lip (NBR) Long term lubrication unit. | █ | █ | █ | 15 | █ | M2×25 | 1,3 | 13 | – | – | – | █ | 400 | |
20 | M2,5×28 | 1,5 | 13 | ||||||||||||
25 | M3×28 | 1,65 | 14 | ||||||||||||
30 | M3×30 | 1,57 | 14 | ||||||||||||
35 | M4×35 | 2,2 | 15 |
Locating face
ACHTUNG
The table is only intended as a guide. Specific application conditions must be taken into consideration when selecting the elements.
The sealing and lubrication elements KIT can be combined flexibly. Recommended and possible combinations, see link. Recommended lubrication connectors, see link.
**Definition, see link.
**Standard for KUVE..-W.
Sealing and lubrication elements KIT (centre)
for KUVE..-W
Designation and KIT end number | Image | Description | Degree of contamination | Size | Retrofittable | Tolerances | Increased displacement force | Designation and KIT end number | |||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
slight | medium | heavy | K1 | LS | S | none | slight | moderate | heavy | ||||||
KIT.KWVE..-W | mm | mm | KIT.KWVE..-W | ||||||||||||
000 | – | No KIT at the corresponding location. | █ | – | – | 15 | █ | – | – | – | █ | – | – | – | 000 |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 | |||||||||||||||
900** | Lower sealing strip, single lip Grooved drive stud (not for size 15). | █ | █ | – | 15 | – | – | – | – | – | █ | – | – | 900** | |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 | |||||||||||||||
910 | Lower sealing strip, single lip Grooved drive stud (not for size 15) Upper sealing strip, single lip. | █ | █ | █ | 15 | – | – | – | – | – | – | █ | – | 910 | |
20 | |||||||||||||||
25 | |||||||||||||||
30 | |||||||||||||||
35 |
ACHTUNG
The table is only intended as a guide. Specific application conditions must be taken into consideration when selecting the elements.
The sealing and lubrication elements KIT can be combined flexibly. Recommended and possible combinations, see link. Recommended lubrication connectors, see link.
**Standard for KUVE..-W.
Possible combinations – KIT allocation (left) to KIT right | ||||||
---|---|---|---|---|---|---|
Designation and |
| |||||
KIT.KWVE..-W | 000 | 100 | 200 | 300 | 370 | 400 |
000 | ● | ‒ | ‒ | ‒ | ‒ | ‒ |
100 | ‒ | ● | ● | ● | ● | ‒ |
200 | ‒ | ● | ● | ● | ● | ‒ |
300 | ‒ | ● | ● | ● | ‒ | ‒ |
370 | ‒ | ● | ● | ‒ | ● | ‒ |
400 | ‒ | ‒ | ‒ | ‒ | ‒ | ● |
●
Possible combination.
Possible combinations – KIT allocation (left or right) to KIT centre | ||||||
---|---|---|---|---|---|---|
Designation and |
| |||||
KIT.KWVE..-W | 000 | 100 | 200 | 300 | 370 | 400 |
000 | ● | ‒ | ‒ | ‒ | ‒ | ‒ |
900 | ‒ | ● | ● | ● | ● | ● |
910 | ‒ | ● | ● | ● | ● | ● |
●
Possible combination.
Definition of side allocation
ACHTUNG
The side allocation of the KIT (left, centre, right) is independent of the orientation of the locating face. When ordering, the required orientation of the locating face (top or bottom) must be indicated.
Lubrication connectors for KUVE..-W
Standard lubrication connectors
Lubrication connectors for manual lubricators
Lubrication connectors for manual lubricators
Size | Positions: | ||||
---|---|---|---|---|---|
Thread | Straight | Angled (45°) | |||
KIT | KIT | ||||
000 100 200 | 300 370 | 000 100 200 | 300 370 | ||
15 | M3 | S16** | ‒ | ‒ | ‒ |
20 | M5 | S02 | S75 | S04** | S13 |
25 | M6 | S03 | S51 | S05** | S14 |
30 | M6 | S03 | S51 | S05** | S14 |
35 | M6 | S03 | S51 | S05** | S14 |
**Standard.
Definition of lubrication connectors
ACHTUNG
The position and alignment of the lubrication connectors is independent of the orientation of the locating face. When ordering, the required orientation of the locating face (top or bottom) must be indicated.
Lubrication connectors for central lubrication
Lubrication connectors for central lubrication
Size | Positions: | ||||
---|---|---|---|---|---|
Thread | Straight | Angled (90°) | |||
KIT | KIT | ||||
000 100 200 | 300 370 | 000 100 200 | 300 370 | ||
15 | M3 | S48 | ‒ | S49 | ‒ |
20 | M5 | S08 | S76 | S46 | S72 |
25 | M6 | S09 | S11 | S42 S61 | S67 |
30 | M6 | S09 | S11 | S42 S61 | S67 |
35 | M6 | S09 | S11 | S42 S61 | S67 |
Definition of lubrication connectors
ACHTUNG
The position and alignment of the lubrication connectors is independent of the orientation of the locating face. When ordering, the required orientation of the locating face (top or bottom) must be indicated.